AP1 cluster into an EG

Connector A ----------------------------------------------- EG harness

EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG

1 BLU/RED (Seat belt reminder) --------------------------- BLU/WHT (B10 Seatbelt Light)

4 PNK (SRS) CONNECT TO +12V power (A10 IGNTION POWER) TO TURN OFF LIGHT (or correct wire if you have it)

6 YEL (Fuse 5) ------ONLY IN CANADA-ONLY IN CANADA-------- BLK/YEL (A10 IGNITION Power)

7 GRN/RED (Left turn signal (+)) ------------------------- GRN/BLU (A4 Left Turn) WORKS

8 GRN/YEL (Right turn signal (+))------------------------- GRN/BLU (A3 RightTurn) WORKS

9 RED/WHT (High beam (+)) -------------------------------- RED/GRN (B1 Highbeam) WORKS

If positive trigger high beam Connect A10 to ground, A9 to switch. If trigger to ground, Connect A9 to Power and A10 to switch. Probably situation 1.

10 RED/BLU (High beam (-)) ------------------------------- BLK (B6 Ground)

11 BLU/BLK (Trunk indicator) ----------------------------- GRN (B9 Trunk Open) WORKS


Connector B

2 RED/YEL (Fuse 45) -------------------------------------- BLK/YEL (A10 Power)

OK, B2 doesn't seem to do ANYTHING. I guess hook it up, I'll look for more details tomorrow.

B3 is the switch between bright and dim. I would connect it to (red/black A11 Gauge Lights)

3 RED/BLK (Circuit 11 – dash and console lights (+)) ----- +12 dims the cluster, so A11 or A12, someone test and I'll edit this.

4 YEL (Fuse 5) ------------------------------------------- BLK/YEL (A10 IGNITION Power)

5 WHT/RED (Fuse 25) -------------------------------------- BLK/YEL (A10 IGNITION Power)

6 GRN (Door Pin Input ground signal) ------------------ Door Pin Switch I can't Find

8 BLK (Ground) ------------------------------------------- BLK (B6 Ground)

9 BLK (Ground) ------------------------------------------- BLK (B6 Ground)

10 RED (Circuit 12 – dash and console lights (-)) -------- BLK (B6 Ground)

Connector C

1 Wht/Blk VSS OUTPUT ------------------------------- Use to connect to regular speedo if ya want. Step down from high pulse rate to regular pulse rate.

3 BLU/WHT (Vehicle speed signal input (-)) --------------- Connect to VSS Converter

5 BLU (RPM signal input) --------------------------------- BLU (A8 Tachometer) Should Work

7 YEL/GRN (Coolant temp input) --------------------------- Connect to ECT Converter

8 YEL/BLK (Fuel gauge signal input) ---------------------- YEL/WHT (A1 Fuel Gauge) Should Work

15 BLU/YEL (Cruise control indicator (-)) ---------------- Cruise Control I can't find, Probably Red with a Blu stripe.. Maybe B3 Probably dont have cruise control WORKS

Connector D

8 BLU/RED (ABS indicator input) Connect to GROUND to turn off light or correct wire if you have it.

9 GRN/WHT (E-brake indicator) ---------------------------- GRN/RED (B2 Brake Light) WORKS

11 WHT/BLU (Charging system indicator (-)) --------------- WHT/BLU (A5 Charging Light) WORKS
(both batt and brake lights come on.)

12 BLK/YEL (Fuse 6) -------------------------------------- BLK/YEL (A10 IGNITION Power)

13 YEL/RED (Engine oil pressure switch input (-)) -------- YEL/RED (A6 Oil Pressure) WORKS

14 GRN/ORN (Malfunction indicator light (-)) ------------- GRN/ORG (B5 MIL Lamp) WORKS

16 WHT/RED (Fuse 25) ------------------------------------- BLK/YEL (A10 IGNITION Power)

this should get you started,i think a couple colors might be off. i just copy/pasted from HT. its defiantly a bitch to get it all perfect but its nice once its done. im about to put mine into my hatch.