another datsun 200sx ka swap, dohc, coupe
12-08-2009, 07:36 PM
#43
Registered Member
Thread Starter
Join Date: Oct 2008
Location: NOVA
Posts: 1,759
Likes: 0
Received 0 Likes
on
0 Posts
Re: another datsun 200sx ka swap, dohc, coupe
yayy wiring for future reference and learning education to others... this principlle is for all swaps basically as long as you figure out the function of the wires
pretty much this breaks it downn
heres the ka
heres the wiring chart
heres the area, drivers side MAF area.. you need those plugs where the stock s12 ENGINE harness was hooked up, which should be removed from the bay by now
heres a few of the needed plugs off the ENGINE harness, to make this unplug and plug the CHASSIS harness...which those stay uncut in the bay...
pretty much just get the desired length, add a bunch of wires. and if your using the same color wire, color code them with color e tape so you know which is which at each end after u bundle them up for less headaches
then, start connecting shit. solder it, (lost my solder. will solder later)
so you do dis, diagram says
BLACK YELLOW<s12 to... ORANGE<s13
which now its
BLACK YELLOW<s12 to WHITE TAPE<harness i made to ORANGE <s13 which you will find located on the s13 harness by the ECU
etc. etc. super simple
pretty much this breaks it downn
heres the ka
heres the wiring chart
heres the area, drivers side MAF area.. you need those plugs where the stock s12 ENGINE harness was hooked up, which should be removed from the bay by now
heres a few of the needed plugs off the ENGINE harness, to make this unplug and plug the CHASSIS harness...which those stay uncut in the bay...
pretty much just get the desired length, add a bunch of wires. and if your using the same color wire, color code them with color e tape so you know which is which at each end after u bundle them up for less headaches
then, start connecting shit. solder it, (lost my solder. will solder later)
so you do dis, diagram says
BLACK YELLOW<s12 to... ORANGE<s13
which now its
BLACK YELLOW<s12 to WHITE TAPE<harness i made to ORANGE <s13 which you will find located on the s13 harness by the ECU
etc. etc. super simple
12-13-2009, 08:01 PM
#46
Registered Member
Thread Starter
Join Date: Oct 2008
Location: NOVA
Posts: 1,759
Likes: 0
Received 0 Likes
on
0 Posts
Re: another datsun 200sx ka swap, dohc, coupe
haha
[youtube]RwJGs05swgY[/youtube]
its on 3 cylinders right now? my sohc did that shit too when i had it half hooked up. once i finish the wiring, hook up a rad, get a intake for it, etc. etc. etc. then hopefully everything should be okay. gotta check the ignition timing too'
techincally ive spent, around 5 days on this, so lets say a week. but it took months because i never really worked on the swap unless lee was here because im broke and shit and hes got the money for parts etc.
kinda sounds like mine when i got it first up
drivetrain together
rear s12 driveshaft, front s13 driveshaft, custom trans mount split between chassis mount and s13 trans mount the all blocked in with poly
i got the jack holding the trans up so it sets
when im done im gonna unbolt the mount, and fill it some more and clean it up
[youtube]RwJGs05swgY[/youtube]
its on 3 cylinders right now? my sohc did that shit too when i had it half hooked up. once i finish the wiring, hook up a rad, get a intake for it, etc. etc. etc. then hopefully everything should be okay. gotta check the ignition timing too'
techincally ive spent, around 5 days on this, so lets say a week. but it took months because i never really worked on the swap unless lee was here because im broke and shit and hes got the money for parts etc.
kinda sounds like mine when i got it first up
drivetrain together
rear s12 driveshaft, front s13 driveshaft, custom trans mount split between chassis mount and s13 trans mount the all blocked in with poly
i got the jack holding the trans up so it sets
when im done im gonna unbolt the mount, and fill it some more and clean it up
Last edited by David S12; 12-13-2009 at 08:05 PM.
12-13-2009, 08:18 PM
#48
Registered Member
Thread Starter
Join Date: Oct 2008
Location: NOVA
Posts: 1,759
Likes: 0
Received 0 Likes
on
0 Posts
12-13-2009, 09:13 PM
#50
Registered Member
Thread Starter
Join Date: Oct 2008
Location: NOVA
Posts: 1,759
Likes: 0
Received 0 Likes
on
0 Posts
Re: another datsun 200sx ka swap, dohc, coupe
then, start connecting shit. solder it, (lost my solder. will solder later)
you dont see the pink heatshrink? its a tad big for larger guage wire but thats all i had to work with and it actually sealed well
the eletrical tape is to discriminate wires... that is all.
