obd-0 to obd-1 need help
#1
obd-0 to obd-1 need help
ok i just got the motor out of my eg but i dont know what to do.i have a
b18a1 from a 90 integra i got a obd 1 harness and a b16 hydro tranny i dont noe wut else to used from my old integra like axles or shiflinkage or motor mounts also wut clutch should i use cuz the ls clutch dont fit the b16 i need alot of help thanx i did research on up but i dint find anything on it so please help thanx alot in advance
b18a1 from a 90 integra i got a obd 1 harness and a b16 hydro tranny i dont noe wut else to used from my old integra like axles or shiflinkage or motor mounts also wut clutch should i use cuz the ls clutch dont fit the b16 i need alot of help thanx i did research on up but i dint find anything on it so please help thanx alot in advance
#4
Registered Member
Join Date: Jan 2007
Location: buena vista virginia
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Re: obd-0 to obd-1 need help
ok i just got the motor out of my eg but i dont know what to do.i have a
b18a1 from a 90 integra i got a obd 1 harness and a b16 hydro tranny i dont noe wut else to used from my old integra like axles or shiflinkage or motor mounts also wut clutch should i use cuz the ls clutch dont fit the b16 i need alot of help thanx i did research on up but i dint find anything on it so please help thanx alot in advance
b18a1 from a 90 integra i got a obd 1 harness and a b16 hydro tranny i dont noe wut else to used from my old integra like axles or shiflinkage or motor mounts also wut clutch should i use cuz the ls clutch dont fit the b16 i need alot of help thanx i did research on up but i dint find anything on it so please help thanx alot in advance
#5
Re: obd-0 to obd-1 need help
get any b series hydro tranny clutch and bseries into eg mounts and shift linkages, you may have to switch the motor mount braket on the motor by the timing belt, use a obd1 ls ecu and you can use the axles and half shaft from the integra and re pin the dizzy from the integra
#7
Registered Member
Join Date: Oct 2003
Location: newport news
Posts: 1,577
Likes: 0
Received 0 Likes
on
0 Posts
Re: obd-0 to obd-1 need help
i have all the mounts from a dc teg you can use i will let em go for 35.00. all you need is the k bracket the half shaft and make sure you have ex hubs up front, you will also need an obd1 dizzy and a p75 i think it is or a p14? not sure had a p75 in mine. you also need the shift linkage from a dc teg just sold mine i think that is all you would need besides the wiring harness off of your old motor you may need to get obd1 injectors.
#8
Re: obd-0 to obd-1 need help
i have all the mounts from a dc teg you can use i will let em go for 35.00. all you need is the k bracket the half shaft and make sure you have ex hubs up front, you will also need an obd1 dizzy and a p75 i think it is or a p14? not sure had a p75 in mine. you also need the shift linkage from a dc teg just sold mine i think that is all you would need besides the wiring harness off of your old motor you may need to get obd1 injectors.
Thread
Thread Starter
Forum
Replies
Last Post
Kris.Is.Foamin
Want to Buy / Trade ARCHIVE
4
12-27-2007 05:23 PM