Relocating the battery to the trunk. Right now, there was 8 gauge wire running to the fuse box, and something a little thicker running to the starter.

I'm going to run a dedicated line from the battery to the fuse box, and a dedicated wire to the starter.

Is 8 gauge wire enough? I've got an assload of 8 gauge amp power wire lying around that'd be perfect for this.

Thanks...

 

No!

1/0 (best choice)
2/0 (better) (most kits come with 2/0)
4/0 (eh)

 

I think that's overkill... the connections on the fuse box and starter really don't hold much more than 8...

 

ya 8 gauge is fine

 

Are you upgrading your battery as well with a higher Amp battery?
The reason the current wire is 8awg, is the car manufacturer's engineer's calculated it according to the distance of the wire and the current draw. If your going to relocate the battery to the trunk, that calculation for an 8awg wire may not work safely. Bigger is better as far as wire gauge is concerned. There are calculations to figure these things out, but you need to know the amp draw and wire distance you're going to use, at least. You don't want to install a small wire and have it burn up on you because it's drawing more amps than what it's rated for. Good luck.

 

The car will only draw the amps that it needs... right? I'm probably just going to go with a standard OEM battery... The only thing I'm running is a standard deck which powers speakers... no subs or anything.

 

No. You're thinking of 2 gauge, not 2/0 gauge. 2/0 is actually 00 gauge, not 2 gauge. Very big difference. 2/0 is 'two ought' meaning 'two zeros'.
4/0 is really fucking huge, almost twice the size of 2/0 and 4 times larger than 2 gauge. Remember, wire sizes get bigger as they go toward zero and then get larger after zero as you get into 0 (1/0), 00 (2/0), 000 (3/0), etc.

2 gauge is more than adequate for most battery relocation, and I wouldn't even bother going larger than 2 gauge because you're not gaining anything. "Bigger is better" isn't always valid. If 2 gauge does the job well, going larger is completely useless and doesn't gain anything except weight, cost, and difficulty routing. You'd have to have a hell of a starter on a hell of an engine and a hell of a long length to need anything bigger than that. This is short duration current remember, so you don't have to worry about constant amperage capacity and current heating and all that stuff.

Basically if the resistance of the wire is low enough to not matter, going to larger wire with lower resistance isn't going to matter any more/less than that. This is like trying to figure out (for example a 250HP turbo setup) whether a 3 inch exhaust is better than a 4 inch (or bigger) exhaust when the 3 inch exhaust has more than enough flow and low enough pressure drop for what you need. You could go 4 inch or larger, but you don't need the flow, it would be more expensive, it's heavier, and good luck trying to fit that under your car.

You're not going to have a wire "burn up on you", don't worry about that. It will get hot for a few seconds during starting, but that's about most current it will ever have going through it and it will cool down after that. Don't use car audio cable for starting systems, use something with a decent insulation quality. Car audio cable may be supple and easy to run, but the insulation isn't very durable or high temp. It's also stupidly expensive because people think they have to pay that price for pretty cable. If you can't find a local place that sells battery cable, try to find welding cable,which works very well also although you might not be able to find it in anything other than black.

 

^ what he said!

 

ohh no run 4 ga up to the firewall and split it into 2 8gs, one to fusebox and one to starter.

 

Oh, I forgot to mention, put a big fuse or puck breaker as close to the battery as possible. That will keep your car from burning to the ground if the cable gets cut, pinched, etc. A battery dump through 4 ga or 2 ga is a lot of power and a lot of heat for a cable to take without protection.