Notices
Tech Talk Anything technically related to your vehicle should be posted here. If you're looking to have work done, try one of the Regional Forums.

DSM, 1g and 2g mixxed parts. (trans/motor)

Thread Tools
 
Old Nov 29, 2005 | 04:13 AM
  #1  
eclpsed's Avatar
eclpsed
Thread Starter
semicolonD.net
 
Joined: Dec 2003
Posts: 3,190
Likes: 0
From: Raleigh, NC
eclpsed eclpsed
Default DSM, 1g and 2g mixxed parts. (trans/motor)

Okie here is my issue, I got one 99 GSX (5spd) with a bad motor. and a 97 GS-T (auto) with a bad tranny. I wanted the GSX to run so i sent both to my friends job and he was going to pull motor from GS-T and toss it into GSX. I didnt do anything to the GS-T just like it is, i didnt do any mods to the car anything, so i know nothing about the GS-T.

My problem, He calledme up and said my flywheel (from GSX) will not bolt up the holes dont match the ones on the motor (from GS-T).. my 1st guess is okie then it's a 6bolt in the GS-T....right? if so do i need a 6bolt tranny? or just a 6 bolt fly wheel?




Thanks for the help!
Old Nov 29, 2005 | 07:03 AM
  #2  
sethmo's Avatar
sethmo
Registered Member
 
Joined: Jul 2005
Posts: 1,595
Likes: 0
From: BFE, Iowa :/
sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

Well only reason it wouldnt bolt up would be because it is a 6bolt, but the 6bolts did not come stock in any 2gs. Someone would have had to do the swap at one point in time. Count the number of bolts on each on the flywheel plate for each motor
Old Nov 29, 2005 | 08:52 AM
  #3  
Hybrid AWD's Avatar
Hybrid AWD
Your Local DSM Tech
 
Joined: Nov 2002
Posts: 6,711
Likes: 0
From: Newport News
Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD Hybrid AWD
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

it's a 6-bolt motor, also be aware that awd and fwd flywheels are different. Sorry I couldnt get back over there Davy. Things have been more than busy for me.
Old Nov 29, 2005 | 05:00 PM
  #4  
MitsuColt's Avatar
MitsuColt
Registered Member
 
Joined: Nov 2005
Posts: 60
Likes: 0
From: VB
MitsuColt is on a distinguished road
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

I think you should get a 6 bolt AWD flywheel, the FWD flywheel is too big . Not a 100% cause i have never done it, but im pretty sure
Old Nov 29, 2005 | 07:56 PM
  #5  
sethmo's Avatar
sethmo
Registered Member
 
Joined: Jul 2005
Posts: 1,595
Likes: 0
From: BFE, Iowa :/
sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo sethmo
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

Yes the FWD flywheel has a slightly larger diameter then the AWD flywheel.
Old Nov 29, 2005 | 09:50 PM
  #6  
Slo DSM's Avatar
Slo DSM
Registered Member
 
Joined: Apr 2004
Posts: 61
Likes: 0
From: Va. Beach
Slo DSM is an unknown quantity at this point
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

Get a 6 bolt awd flywheel. RRE usually has a couple in stock for a decent price. Call Ty and tell him Paul from Va. sent you.
Old Nov 30, 2005 | 12:49 PM
  #7  
eclpsed's Avatar
eclpsed
Thread Starter
semicolonD.net
 
Joined: Dec 2003
Posts: 3,190
Likes: 0
From: Raleigh, NC
eclpsed eclpsed
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

Thanks for the replys, i gotta go by the shop and see what my friend is talkin about something about the flywheel holes are not matchin up with the holes on the motor.. dunno anyways i'll post back up when i see what he's tlakin about...thanks again!
Old Nov 30, 2005 | 02:14 PM
  #8  
MitsuColt's Avatar
MitsuColt
Registered Member
 
Joined: Nov 2005
Posts: 60
Likes: 0
From: VB
MitsuColt is on a distinguished road
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

i know with the flywheel on my motor can only go one one way. made me think about it for a second when i was putting mine bac on after getting it resurfaced but i knew it fit because it came off of that motor, i jsut kept turning it till the holes lined up.
Old Dec 2, 2005 | 11:50 AM
  #9  
eclpsed's Avatar
eclpsed
Thread Starter
semicolonD.net
 
Joined: Dec 2003
Posts: 3,190
Likes: 0
From: Raleigh, NC
eclpsed eclpsed
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

Originally Posted by MitsuColt
i know with the flywheel on my motor can only go one one way. made me think about it for a second when i was putting mine bac on after getting it resurfaced but i knew it fit because it came off of that motor, i jsut kept turning it till the holes lined up.

aye, got we got it on.. jus hand to spin it around a few times hehe..

thanks for the tips!
Old Dec 4, 2005 | 05:31 PM
  #10  
MitsuColt's Avatar
MitsuColt
Registered Member
 
Joined: Nov 2005
Posts: 60
Likes: 0
From: VB
MitsuColt is on a distinguished road
Default Re: DSM, 1g and 2g mixxed parts. (trans/motor)

no problem, glad i could help. now i wish u could tell me what the hell was wrong with my car!
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
HighPSI TSi Guy
Engine / Exhaust / Drivetrain
17
Jun 16, 2009 07:52 AM




All times are GMT -8. The time now is 08:09 PM.