bad sensor or bad timing?
#1
bad sensor or bad timing?
Ok so my sr is being gay again. its bogging. i checked the ecu for codes and it said problem sigh tcam angle sensor. by tps does it mean timing is bad or is the sensor itself bad ?
edit: i ment to say cam angle sensor
edit: i ment to say cam angle sensor
Last edited by LSX240; 10-23-2008 at 04:35 AM.
#2
Re: bad sensor or bad timing?
TPS is throttle position sensor. Doesn't have anything to do with timing. The sensor just measures the throttle plate angle. Very important sensor. It's an analog sensor, meaning the signal varies in voltage with throttle angle. So if you're getting a TPS code, that either means that the sensor is bad (or the wiring is bad) or that the sensor is horribly miscalibrated. Most of them have some adjustability in the mounting such that the sensor can be rotated to match the start point of the angular range with the proper voltage level at that start angle (so the sensor puts out the correct voltage at that position). Generally a mis-calibrated TPS will make the car run poorly, as the airflow into the engine doesn't match what the sensor reading is telling the ECU, but it generally won't trigger a CEL. Most sensor cells require the sensor to be pretty far out of the range the ECU knows to be normal. This is why most automotive sensors read between 0.5 and 4.5 volts, so everything above or below that range can be properly detected as a fault.
That being said, my natural reaction when someone has a SR sensor fault is to blame the wiring. I've seen some horribly fucked up swap wiring, and it doesn't surprise me at all when people have tons of problems getting the engine to run properly. This may or may not apply to your car, but that's always the first place I would look in a swapped car. It's easy to check continuity across the wire from end to end, and check for shorts to ground, etc. Once that's out of the way, you can check to see if the sensor is working properly. TPS sensors are so easy to check though that you can just do that first and then figure out why you're getting a fault. Remember that you have to have 5V, ground, and a signal all connected to the ECU for the sensor to work, so don't just check the signal wire and assume everything is fine.
That being said, my natural reaction when someone has a SR sensor fault is to blame the wiring. I've seen some horribly fucked up swap wiring, and it doesn't surprise me at all when people have tons of problems getting the engine to run properly. This may or may not apply to your car, but that's always the first place I would look in a swapped car. It's easy to check continuity across the wire from end to end, and check for shorts to ground, etc. Once that's out of the way, you can check to see if the sensor is working properly. TPS sensors are so easy to check though that you can just do that first and then figure out why you're getting a fault. Remember that you have to have 5V, ground, and a signal all connected to the ECU for the sensor to work, so don't just check the signal wire and assume everything is fine.
Last edited by Fabrik8; 10-22-2008 at 09:38 PM.
#3
Re: bad sensor or bad timing?
By the way, who did this swap? You've had so many problems with this you might as well take the whole thing out and start again fresh with the wiring and everything.
#4
Re: bad sensor or bad timing?
poop. i ment to say Cam angle sensor. i changed it tho. and idk who did the swap. someone with horrible wiring knowledge tho. but its ok. im in the process of doing it all over again
p.s. when i depress the clutch the rpms stay where they are at or they shoot up about 500 rpms. doesn't that mean my tps(yes i ment tps not cas) is bad anyways?
p.s. when i depress the clutch the rpms stay where they are at or they shoot up about 500 rpms. doesn't that mean my tps(yes i ment tps not cas) is bad anyways?
#5
Re: bad sensor or bad timing?
When you get rid of the parasitic load from the transmission, friction disc, etc., the idle can go up if you're having idle problems. If you have a good, well regulated idle, the idle usually won't go up. The TPS won't change anything unless you change the throttle angle.
#7
Thread
Thread Starter
Forum
Replies
Last Post