no vtec??
#11
Registered Member
Thread Starter
Join Date: Nov 2008
Posts: 173
Likes: 0
Received 0 Likes
on
0 Posts
![Daintegrajdm has disabled reputation](images/reputation/reputation_off.gif)
![Default](images/icons/icon1.gif)
hahaa ok now to sound like a dick but if you read it said i DId get the car to cross into vtec it just wouldnt do it untill late. And yes the head is tapped and the oil passage is blocked off.. the metal in the screen comes from the shavings if your not able to get everything out of the head. IF you read how to build an ls vtec build off of i belive hondaswap magazines website they tell you to use a magnetic drain plug because with the lsvtec at first it will cause for metal shavings but in the end it was because i didnt change the oil soon enough i waited till the first 1500 miles for the oil change. your supposed to do it at the first 100, 500, 1500 then 3000 then every 3 after that.
#12
![Default](images/icons/icon1.gif)
I don't know if this would be the problem you are having but is sort of close to what my crx went through with my b16 swap. If all your wires are correct and dist. is fine and vtec isnt crossing over check the speed sensor. My speed sensor went bad and my vtec did the same thing yours did. Also the circuits on the back of my cluster burned out and vtec didn't work because of that another time. Try to check those two things, I know it sounds odd, but on a odb-o car that was the issue. I could be wrong.
#13
Registered Member
Thread Starter
Join Date: Nov 2008
Posts: 173
Likes: 0
Received 0 Likes
on
0 Posts
![Daintegrajdm has disabled reputation](images/reputation/reputation_off.gif)
![Default](images/icons/icon1.gif)
naa issue is fixed like i was sayin i was using a filter that was too big so once it started to clog it wouldnt get enough oil pressure. so once i put a smaller filter on there it was good just changed oil vtec screen and it was good. runs great now.. now just starting on that wire tuck!
#14
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
Soooo why would a filter that is too big cause a problem with low oil pressure? It must have been a horrible quality filter and would have caused a problem no matter what size it was.
#15
Registered Member
Thread Starter
Join Date: Nov 2008
Posts: 173
Likes: 0
Received 0 Likes
on
0 Posts
![Daintegrajdm has disabled reputation](images/reputation/reputation_off.gif)
![Default](images/icons/icon1.gif)
There is three differnt filters for hondas for non vtec cars you have the biggest filter for cars like early accords with the single cam motors. Then the new accords and civics have another filter which is designed for vtec so that it will keep a high oil pressure but not high enough to damage the oil filter or the oil system in the car. Then on some of the newer civics with non vtec single cams they have the smallest filter. My car had the filter that you put on the older style single cams keeping a lower oil pressure so i had to switch to a smaller vtec filter.
Just case your wondering i work at an instant oil change place so i have to keep these kind of things in mind dumb shit i know
Just case your wondering i work at an instant oil change place so i have to keep these kind of things in mind dumb shit i know
#16
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
So like I said, you're using a poor quality filter. The better filters (for the VTEC engines) are less restrictive so the oil pressure is higher. The non-VTEC filters, which I assume are also cheaper (at least to manufacture, even if the price is the same) are more restrictive which makes the oil pressure lower. That's not something that you really want for most engines, because you can't oil a tight tolerance engine (or an engine that needs high oil flow) by using low oil pressure.
So yes, a decent oil filter is what you need.
And what's wrong with your engine that's making you clog oil filters????? You shouldn't be making shavings in the engine, because you're not changing anything about the engine. Putting a different head on an existing block doesn't make you start producing metal shavings. If you're getting shavings, they have to be from the machining operations and not the engine running. If that's not the case, you have a VERY damaged engine.
So yes, a decent oil filter is what you need.
And what's wrong with your engine that's making you clog oil filters????? You shouldn't be making shavings in the engine, because you're not changing anything about the engine. Putting a different head on an existing block doesn't make you start producing metal shavings. If you're getting shavings, they have to be from the machining operations and not the engine running. If that's not the case, you have a VERY damaged engine.
Last edited by Fabrik8; 07-13-2009 at 05:13 PM.
#17
OM NOM NOM E30
Join Date: Nov 2002
Location: Portsmouth
Posts: 5,001
Likes: 0
Received 0 Likes
on
0 Posts
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
So like I said, you're using a poor quality filter. The better filters (for the VTEC engines) are less restrictive so the oil pressure is higher. The non-VTEC filters, which I assume are also cheaper (at least to manufacture, even if the price is the same) are more restrictive which makes the oil pressure lower. That's not something that you really want for most engines, because you can't oil a tight tolerance engine (or an engine that needs high oil flow) by using low oil pressure.
So yes, a decent oil filter is what you need.
And what's wrong with your engine that's making you clog oil filters????? You shouldn't be making shavings in the engine, because you're not changing anything about the engine. Putting a different head on an existing block doesn't make you start producing metal shavings. If you're getting shavings, they have to be from the machining operations and not the engine running. If that's not the case, you have a VERY damaged engine.
So yes, a decent oil filter is what you need.
And what's wrong with your engine that's making you clog oil filters????? You shouldn't be making shavings in the engine, because you're not changing anything about the engine. Putting a different head on an existing block doesn't make you start producing metal shavings. If you're getting shavings, they have to be from the machining operations and not the engine running. If that's not the case, you have a VERY damaged engine.
see here was mine.
![](http://members.bellatlantic.net/~vze2qzh9/vtec.jpg)
oh and this what my bear for #1 looked like.
![](http://members.bellatlantic.net/~vze2qzh9/bearing1.jpg)
Even gave me custom type r cams.
![](http://members.bellatlantic.net/~vze2qzh9/cam2.jpg)
With matching cam journals!
![](http://members.bellatlantic.net/~vze2qzh9/camjournal.jpg)
But i bet he's fine, cause they all do that.
#19
OM NOM NOM E30
Join Date: Nov 2002
Location: Portsmouth
Posts: 5,001
Likes: 0
Received 0 Likes
on
0 Posts
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_pos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![JETSWU87](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
Shit was bad, everything was trashed. Reused the bare block, and rods....thats it. sigh
live and learn
#20
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
I figured you got it from someone else because of your sense of humor. Not many people would own up to trashing an engine like that if it was their fault, so I assumed it didn't die by your hand.
Thread
Thread Starter
Forum
Replies
Last Post
gotboosthatch
Import - ASIA
27
12-18-2008 03:55 PM
Woodpsuher50mm
Want to Buy / Trade ARCHIVE
0
06-01-2008 06:34 PM
Tim-Tim
Want to Buy / Trade ARCHIVE
9
01-29-2008 07:19 PM