How do i bleed the tranny
#1
Registered Member
Thread Starter
Join Date: Mar 2009
Location: richmond
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
![fingers can only hope to improve](images/reputation/reputation_neg.gif)
![Default](images/icons/icon1.gif)
I have a 92 prelude with the stock h23 tranny and i took the lines off to pull motor and tranny out so i could replace motor now i need to bleed the tranny. What is the correct way to go about that
#2
I Love to Hate
Join Date: Mar 2006
Location: Va Beach
Posts: 6,777
Likes: 0
Received 0 Likes
on
0 Posts
![B-Well](images/reputation/reputation_pos.gif)
![B-Well](images/reputation/reputation_pos.gif)
![B-Well](images/reputation/reputation_pos.gif)
![B-Well](images/reputation/reputation_pos.gif)
![B-Well](images/reputation/reputation_pos.gif)
![B-Well](images/reputation/reputation_highpos.gif)
![B-Well](images/reputation/reputation_highpos.gif)
![B-Well](images/reputation/reputation_highpos.gif)
![B-Well](images/reputation/reputation_highpos.gif)
![B-Well](images/reputation/reputation_highpos.gif)
![B-Well](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
you are bleeding the clutch.
two person job
one person(1) in drivers seat the other(2) with a 10mm line wrench on the bleeder of the slave cyl.
1 pushes clutch pedal to the floor and holds
2 opens the bleeder slightly to let some air out then shuts it
1 lifts pedal up and presses again
2 opens and closes bleader again
continue untill fluid has no air bubbles (i like to continue till the fluid is clear)
it is wise to connect a hose to the bleeder nipple and put it into a beer can with the tab reversed. this keeps the mess contained. Remember to keep the master cyl filled with fluid the whole time. dot3+ brake fluid can be used
#4
Registered Member
Thread Starter
Join Date: Mar 2009
Location: richmond
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
![fingers can only hope to improve](images/reputation/reputation_neg.gif)
![Default](images/icons/icon1.gif)
[QUOTE=B-Well;5450547]stick finger in, crank motor, bleed all over tranny
you are bleeding the clutch.
two person job
one person(1) in drivers seat the other(2) with a 10mm line wrench on the bleeder of the slave cyl.
1 pushes clutch pedal to the floor and holds
2 opens the bleeder slightly to let some air out then shuts it
1 lifts pedal up and presses again
2 opens and closes bleader again
continue untill fluid has no air bubbles (i like to continue till the fluid is clear)
it is wise to connect a hose to the bleeder nipple and put it into a beer can with the tab reversed. this keeps the mess contained. Remember to keep the master cyl filled with fluid the whole time. dot3+ brake fluid can be used[/QU thanks dude
you are bleeding the clutch.
two person job
one person(1) in drivers seat the other(2) with a 10mm line wrench on the bleeder of the slave cyl.
1 pushes clutch pedal to the floor and holds
2 opens the bleeder slightly to let some air out then shuts it
1 lifts pedal up and presses again
2 opens and closes bleader again
continue untill fluid has no air bubbles (i like to continue till the fluid is clear)
it is wise to connect a hose to the bleeder nipple and put it into a beer can with the tab reversed. this keeps the mess contained. Remember to keep the master cyl filled with fluid the whole time. dot3+ brake fluid can be used[/QU thanks dude
#6
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
Thread
Thread Starter
Forum
Replies
Last Post
4g638u
Engine / Exhaust / Drivetrain
2
03-24-2010 03:17 PM
radiaki11
Parts ARCHIVE
2
12-14-2008 08:28 PM