S12 Project
#1
Registered Member
Thread Starter
Join Date: Nov 2007
Location: Dinwiddie County (23803), VA
Posts: 361
Likes: 0
Received 0 Likes
on
0 Posts
S12 Project
Selling a 1987 Nissan 200SX with a CA20E and 5-speed. Runs, but is running rough. May need rings if you keep the engine. Could use two front fenders (portions behind both front tires are rusted out) and the right rear quarter panel is dinged in. Has no interior other than the front seats, dash, and most of the center console.
However, it will come with a KA24E from a 89-92 S13 240SX with manual transmission, stock KA 5-speed ECU, KA24DE plastic MAF and KA24E metal MAF, stock and 450CC injectors (low impedance, and have new injector O-rings for four injectors), cut spare and uncut engine harness, long tube header for the KA and exhaust manifold gaskets, Eaton M90 supercharger from a Pontiac Grand Prix GTP, two spare wheels, two universal fiberglass fender flares, and MSD SCI ignition box.
Willing to trade for stock 91-94 Nissan Sentra 2-door, Nissan 2WD Hardbody D21 4-cylinder Pickup, rust free Datsun/Nissan 720 2WD pickup, 96 Nissan 200SX, or a decent, rust free street legal, Datsun RWD car. Will only take manual transmission vehicles. Or I will take $1200 cash. Use the thread or PM for contact and need to get it gone ASAP. This was a project I thought I would have the time to do, but I just don't. Would like to have a Nissan/Datsun in time for a Nissan Meet in Hampton Roads next week.
However, it will come with a KA24E from a 89-92 S13 240SX with manual transmission, stock KA 5-speed ECU, KA24DE plastic MAF and KA24E metal MAF, stock and 450CC injectors (low impedance, and have new injector O-rings for four injectors), cut spare and uncut engine harness, long tube header for the KA and exhaust manifold gaskets, Eaton M90 supercharger from a Pontiac Grand Prix GTP, two spare wheels, two universal fiberglass fender flares, and MSD SCI ignition box.
Willing to trade for stock 91-94 Nissan Sentra 2-door, Nissan 2WD Hardbody D21 4-cylinder Pickup, rust free Datsun/Nissan 720 2WD pickup, 96 Nissan 200SX, or a decent, rust free street legal, Datsun RWD car. Will only take manual transmission vehicles. Or I will take $1200 cash. Use the thread or PM for contact and need to get it gone ASAP. This was a project I thought I would have the time to do, but I just don't. Would like to have a Nissan/Datsun in time for a Nissan Meet in Hampton Roads next week.
#2
Registered Member
Thread Starter
Join Date: Nov 2007
Location: Dinwiddie County (23803), VA
Posts: 361
Likes: 0
Received 0 Likes
on
0 Posts
Re: S12 Project
The brakes, just as another note, are spongy, but it will come with new brake lines (that I got from Rock Auto) and NAPA Safety Stop pads for front and rear. These fit the stock, CA20E car and are not an upgrade. The plugs, cap, rotor, and spark plugs in the CA are also new.
I will also throw in a Grant steering wheel and a S13 adapter (which I have been told might fit), and some Amsoil that I have in the car.
Hope someone with more time and space can get this car, and I'm just looking for a stock car, nothing special (hell, it can even be a CA18ET or another CA20E car, just so long as it's not another project for now). Paint can be ratty, interior can be a little rough, but so long as it runs, drives, and I wouldn't have any trouble taking it further than point a and b, would be all I'm looking for in a trade. I can even add money if that will help the deal.
I will also throw in a Grant steering wheel and a S13 adapter (which I have been told might fit), and some Amsoil that I have in the car.
Hope someone with more time and space can get this car, and I'm just looking for a stock car, nothing special (hell, it can even be a CA18ET or another CA20E car, just so long as it's not another project for now). Paint can be ratty, interior can be a little rough, but so long as it runs, drives, and I wouldn't have any trouble taking it further than point a and b, would be all I'm looking for in a trade. I can even add money if that will help the deal.
#3
Registered Member
Join Date: Jul 2010
Location: Gloucester VA
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Re: S12 Project
are you willing to part it out bc i need the uncut wirring harness
#4
Registered Member
Thread Starter
Join Date: Nov 2007
Location: Dinwiddie County (23803), VA
Posts: 361
Likes: 0
Received 0 Likes
on
0 Posts
Re: S12 Project
No, I can not and will not part it out.
Thread
Thread Starter
Forum
Replies
Last Post