stereo questions "help asap need to get this tonight"
#11
VaDriven Mayhem
Join Date: Sep 2004
Location: Where the faggles are.
Posts: 21,312
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
Lulz at the stupidity of needing 4 10s and a 15.
OP is probably an asshole that drives through neighborhoods at 3am with the stereo turned way up
OP is probably an asshole that drives through neighborhoods at 3am with the stereo turned way up
#12
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
Don't worry about PWM. Pretty much every car audio amp uses a PWM power supply, unless they use some other less common power supply architecture. Basically a PWM power supply takes the 12V from the car's electrical system and turns it into higher voltage to power the amplifier section of the amp. Pyle makes low-end products, so they're trying to make their specifications sound important even though every other amp on the market does the exact same thing.
It's like buying a car sometime during the last 70 years, and the spec sheet on the car says "internal combustion engine". It's redundant, just like saying a car audio amp has a PWM power supply.
It's like buying a car sometime during the last 70 years, and the spec sheet on the car says "internal combustion engine". It's redundant, just like saying a car audio amp has a PWM power supply.
#13
baller/dickbutt#69
Join Date: Nov 2002
Location: hampton
Posts: 16,059
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
ok so im looking to buy a 3000 or 4000 watt amp and a capacitor, on the capacitor i was wondering how to rate the "farads" and on the amp i was wondering what the "PWM ( Pulse-Width-Modulation ) System" is for and what it affects.
please help me out asap i need to order this tonight thanks
please help me out asap i need to order this tonight thanks
amp specs-
* NEW PYLE 4 Channel 4000 Watts Bridgeable Mosfet Amplifier
* Maximum Power Output 4 x 1000W
* Bridgeable RMS Power @ 4 Ohms: 2 x 2000W
* 4 Channel Bridgeable MOSFET Amplifier
* Frequency Response 20 Hz-50kHz (±3dB)
* Output Power @ 14.4v DC, 50Hz
* 2 Ohm Stable
* MOSFET Power Supply
* PWM ( Pulse-Width-Modulation ) System
* Glass Epoxy PCB
* Silver RCA Inputs
* Custom Terminal Block for Speaker Connection
* Thermal / Overload / Short Circuit Protection
* Input Impedance: 47K Ohms
* Soft Turn On/ Off
* Advanced Protection Circuitry
* S/N Ratio: >90dB
* Dimensions:10.24''W x 2.21''H x 17.72''L
* 1 Year Manufacturer Warranty
* NEW PYLE 4 Channel 4000 Watts Bridgeable Mosfet Amplifier
* Maximum Power Output 4 x 1000W
* Bridgeable RMS Power @ 4 Ohms: 2 x 2000W
* 4 Channel Bridgeable MOSFET Amplifier
* Frequency Response 20 Hz-50kHz (±3dB)
* Output Power @ 14.4v DC, 50Hz
* 2 Ohm Stable
* MOSFET Power Supply
* PWM ( Pulse-Width-Modulation ) System
* Glass Epoxy PCB
* Silver RCA Inputs
* Custom Terminal Block for Speaker Connection
* Thermal / Overload / Short Circuit Protection
* Input Impedance: 47K Ohms
* Soft Turn On/ Off
* Advanced Protection Circuitry
* S/N Ratio: >90dB
* Dimensions:10.24''W x 2.21''H x 17.72''L
* 1 Year Manufacturer Warranty
a jl amp or older us amp/rockford amps will be ten times better than a pyle amp...
find a old zues hyphonics amp on ebay...
and are you building a bass contest vehicle or doing it because it will "hit hard" ?
cause there are a ton better speakers that will hit a whole lot harder..for less speakers..
#14
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
What I want to know is how the PLA1200 amp (on Pyle's site) is rated at 600W RMS at 14.4V with a 40A fuse. 14.4 x 40 = 576W, and that doesn't even include power supply efficiency and output stage efficiency, so it's impossible to have 600W of output power from 576W of input power. Their rating system is flawed, or they're really big liars.
#16
VaDriven Mayhem
Join Date: Sep 2004
Location: Where the faggles are.
Posts: 21,312
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
What I want to know is how the PLA1200 amp (on Pyle's site) is rated at 600W RMS at 14.4V with a 40A fuse. 14.4 x 40 = 576W, and that doesn't even include power supply efficiency and output stage efficiency, so it's impossible to have 600W of output power from 576W of input power. Their rating system is flawed, or they're really big liars.
#17
Registered Member
Thread Starter
Join Date: Feb 2010
Posts: 509
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
im building it to see what it will do just out of curiosity its like a project for me, pretty much a practicing thing ive never tried hooking up subs etc.
#18
VaDriven Mayhem
Join Date: Sep 2004
Location: Where the faggles are.
Posts: 21,312
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
#19
Registered member
Join Date: Sep 2006
Location: Norfolk
Posts: 2,250
Likes: 0
Received 0 Likes
on
0 Posts
Re: stereo questions "help asap need to get this tonight"
Op don't waist your money. You can get much better stuff for way cheaper. If you look on cragslist you can find some nice subs and an amp for like $200-$300. But if you realy want to get a Pyle of shit amp and mismatch your subs that's upto you.
Thread
Thread Starter
Forum
Replies
Last Post