jdm b16 throwing a code
#2
Re: jdm b16 throwing a code
7 TP Sensor (Throttle Position) sensor
1)it could be broke or bad
2)if you have a 4g multi port then you need to switch the (green/white and yellow/white )
if it bad/broke then it's not that bad to swith out...
1)it could be broke or bad
2)if you have a 4g multi port then you need to switch the (green/white and yellow/white )
if it bad/broke then it's not that bad to swith out...
#6
____________
Join Date: Mar 2004
Location: Northern Virginia
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Re: jdm b16 throwing a code
Here you go, by Pills_PMD in hondaswap.com, hope it helps.
How to Check the Voltage on your Throttle Position Sensor.
After performing a swap, many times the throttle position sensor on the engine is broken, forcing you to use one from your old d15 or d16 (or whichever you pulled). The Honda TPS has three wires coming from it: green/white , a red/blue , yellow/white. Your primary focus will be on the red/blue wire, as this is the one that sends a voltage to the ECU telling it how open or closed your throttle is. The ECU expects .5 volts to be closed throttle and 4.5 volts to be Wide Open Throttle (WOT). The red/blue wire goes to pin D11 at the ECU. Rotating the TPS will change the voltage, when you take it off, you'll notice that the holes are slotted so it can move. If you are fortunate enough to have Hondata Datalogging or an Apexi V-AFC you can use their inbuilt functions to read the TPS voltage. If you do not have such a device, you can use a Voltmeter or similar device. Ground one lead on the chassis somewhere and use touch the (+) lead to the pin on the TPS (should be the center pin) and measure the voltage. Rotate it until it reads .5 volts, then tighten it down. Have a friend press the gas pedal to the floor and also check that WOT reads 4.5 volts.
For those interested with the other two leads, and I know there has to be someone out there. The green/white wire ties into a braided wire with the Intake Air Temp Sensor and the Heated Oxygen Sensor and they all run to Pin D22 on the ECU which is a sensor ground that reads less than 1 volt while the car is started. The yellow/white wire goes to pin D20 on the ECU which is a reference voltage, where it gives about 5v with the Key on and engine off.
After performing a swap, many times the throttle position sensor on the engine is broken, forcing you to use one from your old d15 or d16 (or whichever you pulled). The Honda TPS has three wires coming from it: green/white , a red/blue , yellow/white. Your primary focus will be on the red/blue wire, as this is the one that sends a voltage to the ECU telling it how open or closed your throttle is. The ECU expects .5 volts to be closed throttle and 4.5 volts to be Wide Open Throttle (WOT). The red/blue wire goes to pin D11 at the ECU. Rotating the TPS will change the voltage, when you take it off, you'll notice that the holes are slotted so it can move. If you are fortunate enough to have Hondata Datalogging or an Apexi V-AFC you can use their inbuilt functions to read the TPS voltage. If you do not have such a device, you can use a Voltmeter or similar device. Ground one lead on the chassis somewhere and use touch the (+) lead to the pin on the TPS (should be the center pin) and measure the voltage. Rotate it until it reads .5 volts, then tighten it down. Have a friend press the gas pedal to the floor and also check that WOT reads 4.5 volts.
For those interested with the other two leads, and I know there has to be someone out there. The green/white wire ties into a braided wire with the Intake Air Temp Sensor and the Heated Oxygen Sensor and they all run to Pin D22 on the ECU which is a sensor ground that reads less than 1 volt while the car is started. The yellow/white wire goes to pin D20 on the ECU which is a reference voltage, where it gives about 5v with the Key on and engine off.
Thread
Thread Starter
Forum
Replies
Last Post