Running into problems while installing my Skunk2 front camber kit on 95 civic
07-12-2004, 08:29 AM
#11
takin it all
Join Date: Jan 2003
Location: 757/PA/MD/Boston,MA
Posts: 6,934
Likes: 0
Received 0 Likes
on
0 Posts
Re: Running into problems while installing my Skunk2 front camber kit on 95 civic
ratchet/wrench with a hammer, hit it a couple times it acts like an impact wrench, safe way not to break bolts also
07-12-2004, 08:32 AM
#12
UNCE UNCE UNCE UNCE
Join Date: Jun 2004
Location: J'Ville FL.
Posts: 9,811
Likes: 0
Received 0 Likes
on
0 Posts
Re: Running into problems while installing my Skunk2 front camber kit on 95 civic
Originally Posted by slimstajimsta5
ahh i screwed up saying that.. i meant the dust boot around the ball joint that's rubber. sorry for the confusion. i just used a knife and got it off. it was soo gewwy with grease when i cut it open.
thanks for the help
now i ran into another problem though. the 2 pivot bolts that are on my control arm are on so tight i can't get them off because i don't have airtools and i'm doing this by myself. i couldn't even get the fuckers to budge at all. i think i'll just go to tuners edge real quick and hopefully get them to take it off for me.
well that's all for now. thanks again
thanks for the help
now i ran into another problem though. the 2 pivot bolts that are on my control arm are on so tight i can't get them off because i don't have airtools and i'm doing this by myself. i couldn't even get the fuckers to budge at all. i think i'll just go to tuners edge real quick and hopefully get them to take it off for me.
well that's all for now. thanks again
Take your ass to the gym and you'll get it off!!
J/K Yeah but like ^^ said. A ratchet and a hammer should do it.
07-12-2004, 09:04 AM
#13
takin it all
Join Date: Jan 2003
Location: 757/PA/MD/Boston,MA
Posts: 6,934
Likes: 0
Received 0 Likes
on
0 Posts
Re: Running into problems while installing my Skunk2 front camber kit on 95 civic
just make sure you keep the wrech all the way on the bolt/nut dont round that shit off
07-12-2004, 10:50 AM
#15
Eat me.
Thread Starter
Join Date: May 2003
Location: seven eleven plus the fo' six
Posts: 13,798
Likes: 0
Received 0 Likes
on
0 Posts
Re: Running into problems while installing my Skunk2 front camber kit on 95 civic
i just took it to tuners edge and they got it off in no time. they are awesome haha
07-12-2004, 04:28 PM
#17
Eat me.
Thread Starter
Join Date: May 2003
Location: seven eleven plus the fo' six
Posts: 13,798
Likes: 0
Received 0 Likes
on
0 Posts
Re: Running into problems while installing my Skunk2 front camber kit on 95 civic
i'll be honest and say i don't know what an impact wrench is. i've probably seen it and used one but i'm not familiar with all the correct terminology
well, i got it all finished around 7. if i worked on it the whole time without a bunch of breaks, it would have been done alot earlier
thanks for the help you guys
well, i got it all finished around 7. if i worked on it the whole time without a bunch of breaks, it would have been done alot earlier
thanks for the help you guys
Thread
Thread Starter
Forum
Replies
Last Post