4x4 Off Topic Thread
OCD Fag.
Joined: Oct 2010
Posts: 891
Likes: 0
From: RVA
Re: 4x4 Off Topic Thread
The Banks muffler on my truck finally rusted though, replacing it with a Flowmaster setup...nothing to exciting. I'm hoping it sounds better behind my 460 than Flowmasters site with it installed on an older Silverado. The Banks catback is 12 years old, so I'm not complaining.
What size pipes do you have, er, are going with?
WHITE TRASH
Joined: Oct 2005
Posts: 2,972
Likes: 0
From: I-64, I-464, I-264, I-664
Re: 4x4 Off Topic Thread
The cat back is 3" and the muffler is 3" in and out. It has long tubes and 3" y-pipe. The Flowmaster muffler is a 70 series. It's the only reasonably priced system for my truck. I searched Jeggs and Summit by make model and engine...The Banks system was 3x as much. My Corvette needs tires soon so I went with it to save a few $
Registered Member
Joined: Apr 2010
Posts: 1,058
Likes: 0
From: va beach
Re: 4x4 Off Topic Thread
http://www.youtube.com/watch?v=-PF51c-l0zE
in this i thought he just snapped another shaft like he always does. but he was just 2wd the whole time.
http://www.youtube.com/watch?v=p67rSpo-MGQ
http://www.youtube.com/watch?v=p67rSpo-MGQ
OCD Fag.
Joined: Oct 2010
Posts: 891
Likes: 0
From: RVA
Re: 4x4 Off Topic Thread
The cat back is 3" and the muffler is 3" in and out. It has long tubes and 3" y-pipe. The Flowmaster muffler is a 70 series. It's the only reasonably priced system for my truck. I searched Jeggs and Summit by make model and engine...The Banks system was 3x as much. My Corvette needs tires soon so I went with it to save a few $
WHITE TRASH
Joined: Oct 2005
Posts: 2,972
Likes: 0
From: I-64, I-464, I-264, I-664
Re: 4x4 Off Topic Thread
It's on. Quieter than the Banks and that's fine. Flowmaster has this stuff figured out, it fit PERFECT. No hassles and no headaches..except taking the rusty Banks stuff off. Nothing the air chisel couldn't handle though.
Registered Member
Joined: Apr 2010
Posts: 1,058
Likes: 0
From: va beach
Re: 4x4 Off Topic Thread
so.. 3/4 bolts holding the drivers side radius arm to the frame that are all loose, 2/4 bolts holding the passenger side that are loose also. having to completely detach the axle from the brackets and they STILL wont line up to put bolts in.... finding out my passenger caliper was missing a slide pin. had to remove the driveshaft from the yolk to drop the axle and needle bearings going everywhere. and i still havent gotten those bolts in yet.
all cause i took my fender off to make a snorkel... which still aint done either...
all cause i took my fender off to make a snorkel... which still aint done either...
Awesome.
Joined: Nov 2002
Posts: 13,483
Likes: 0
From: Virginia Beach
Re: 4x4 Off Topic Thread
[QUOTE=irfreddy;7835155][video=youtube;-PF51c-l0zE]http://www.youtube.com/watch?v=-PF51c-l0zE[video]
in this i thought he just snapped another shaft like he always does. but he was just 2wd the whole time.
http://www.youtube.com/watch?v=p67rSpo-MGQ [QUOTE]
Can't believe he was using them as little jumps. Haha
in this i thought he just snapped another shaft like he always does. but he was just 2wd the whole time.
http://www.youtube.com/watch?v=p67rSpo-MGQ [QUOTE]
Can't believe he was using them as little jumps. Haha
