Throwout Bearing?
12-04-2010, 02:41 PM
シビックタイプR
Thread Starter
Join Date: May 2010
Location: Norfolk, VA
Posts: 1,340
Likes: 0
Received 0 Likes
on
0 Posts
Throwout Bearing?
Is there anyway to slightly move the trhow out bearing on the tranny? its too far forward and touches the pressure plate at idle
12-04-2010, 02:51 PM
Registered Member
Join Date: Jun 2007
Location: portsmouth v.a
Posts: 476
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
ur throwout fork mite be bent what kinda car is it in and what kind of clutch setup?
12-04-2010, 03:48 PM
シビックタイプR
Thread Starter
Join Date: May 2010
Location: Norfolk, VA
Posts: 1,340
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
its a gsr swap. had a stock clutch on it before i just installed a stage four not even a week ago
12-04-2010, 05:28 PM
Registered Member
Join Date: Jun 2007
Location: portsmouth v.a
Posts: 476
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
def check ur clutch fork does it drive and shift fine and what makes u think its touching or have u visibley looked in the hole ?
12-04-2010, 05:33 PM
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
Also check the clutch pedal adjustment to see if the pedal position is preloading the slave cylinder.
12-04-2010, 07:11 PM
シビックタイプR
Thread Starter
Join Date: May 2010
Location: Norfolk, VA
Posts: 1,340
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
Quote:
Originally Posted by
Fabrik8
Also check the clutch pedal adjustment to see if the pedal position is preloading the slave cylinder.
That's what I think it is how do I adjust it?
12-04-2010, 08:06 PM
Registered Member
Join Date: Oct 2010
Location: Virginia Beach
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
Quote:
Originally Posted by
boostorbust
That's what I think it is how do I adjust it?
it should just be a bolt that threads into a nut. get under your steering column and look at it, its hard to miss.
12-05-2010, 05:27 AM
Registered Member
Join Date: Jun 2007
Location: portsmouth v.a
Posts: 476
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
and jus for shit and giggles bleed ur clutch line mite have air
12-05-2010, 12:55 PM
シビックタイプR
Thread Starter
Join Date: May 2010
Location: Norfolk, VA
Posts: 1,340
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
I used a vacuum pump and bled it today I think it was that, it shifts perfect just a lil noisy at low rpm
12-05-2010, 01:59 PM
Registered Member
Join Date: Jun 2007
Location: portsmouth v.a
Posts: 476
Likes: 0
Received 0 Likes
on
0 Posts
Re: Throwout Bearing?
what kind of noise?Did u line the clutch up properly and torque it in the rite pattern also did you change throwout bearing or did you use the old one and dont forget to break your clutch in 500 miles