Notices
Automotive Discussion Automotive talk that is not technical can be posted here. Posts must address the general population.

First time at track

Thread Tools
 
Old 04-02-2003 | 03:01 AM
  #1  
Seye's Avatar
Seye
Thread Starter
Registered Member
 
Joined: Dec 2002
Posts: 97
Likes: 0
Seye is an unknown quantity at this point
Default First time at track

I went to the track for the first time over the weekend! Didnt go too bad, i had some problems with wheel hop. Im going to order a bushing kit today to help out with that. What other little small things would help me? I got a stage two clutch, resurfaced flywheel, intake and 2 1/2" piping w/magnaflow muffler.Im hoping to do better this weekend when i go.

My Best

R/T-.565
60'.-2.428
330-6.533
1/8-9.902
MPH-73.71
1000-12.793
1/4-15.249
MPH-91.64
Old 04-02-2003 | 03:06 AM
  #2  
sprayn93's Avatar
sprayn93
Registered Member
 
Joined: Nov 2002
Posts: 151
Likes: 0
From: Portsmouth
sprayn93 sprayn93 sprayn93 sprayn93 sprayn93 sprayn93 sprayn93 sprayn93 sprayn93 sprayn93 sprayn93
Default

A 60 foot 2.4 sucks. You need a set of slicks. What rpm are you launching from? With a better 60ft you would be in the 14.s. Advance your timing and run some race fuel.
Old 04-02-2003 | 03:09 AM
  #3  
G60ING's Avatar
G60ING
Corrado Butcher
 
Joined: Nov 2002
Posts: 325
Likes: 0
From: south of the boarder
G60ING is an unknown quantity at this point
Default

your r/t is good for your first time. Nice job. The 60' will come with more experiance and more control.
Old 04-02-2003 | 03:12 AM
  #4  
Seye's Avatar
Seye
Thread Starter
Registered Member
 
Joined: Dec 2002
Posts: 97
Likes: 0
Seye is an unknown quantity at this point
Default

like i said it was my first time, i think on this run i launched at 3000 rpm, no matter what i did i either spun through first or had wheel hop halfway throgh first.
Old 04-02-2003 | 08:58 AM
  #5  
G60ING's Avatar
G60ING
Corrado Butcher
 
Joined: Nov 2002
Posts: 325
Likes: 0
From: south of the boarder
G60ING is an unknown quantity at this point
Default

Thats part of control. I know people with 115 crank HP that can't control their cars in 1st and 2nd gear and wonder why they ran a 17sec run. Well if you can't control that then you will have even more problems with 200whp. its all about getting the 60' times down which basically means 1st and 2nd. It can be done without drag slicks
Old 04-02-2003 | 09:13 AM
  #6  
EEK's Avatar
EEK
卐 Walnuts
 
Joined: Nov 2002
Posts: 29,360
Likes: 0
From: Compton, Ca W
EEK EEK EEK EEK EEK EEK EEK EEK EEK EEK EEK
Default

what motor and what year hatch?
Old 04-02-2003 | 01:23 PM
  #7  
Seye's Avatar
Seye
Thread Starter
Registered Member
 
Joined: Dec 2002
Posts: 97
Likes: 0
Seye is an unknown quantity at this point
Default

Originally posted by EEK
what motor and what year hatch?
sorry, 95 b18b in my 95cx hatch
Old 04-03-2003 | 05:17 AM
  #8  
EEK's Avatar
EEK
卐 Walnuts
 
Joined: Nov 2002
Posts: 29,360
Likes: 0
From: Compton, Ca W
EEK EEK EEK EEK EEK EEK EEK EEK EEK EEK EEK
Default

u should be hittin a 14.9/15.0
Old 04-03-2003 | 07:07 AM
  #9  
thelastmirage's Avatar
thelastmirage
Banned
 
Joined: Dec 2002
Posts: 135
Likes: 0
thelastmirage is an unknown quantity at this point
Default

to prevent wheel hop I would go get better engine mounts. you could also get a two step launch system or just feather your clutch slightly so you will not spin.
Old 04-03-2003 | 09:13 AM
  #10  
Whtehnda93DXSdn's Avatar
Whtehnda93DXSdn
It has 4 Doors...
 
Joined: Nov 2002
Posts: 326
Likes: 0
From: Fredericksburg,Va
Whtehnda93DXSdn is an unknown quantity at this point
Default

those figures aren;t to bad at all for the 1st time at the track....As you go a bit more you will get better and inprove and learn the tricks of the trade of racing.

That RT was real nice keep that up for sure....


Quick Reply: First time at track



All times are GMT -8. The time now is 02:22 AM.