Jdm gsr swap help
#1
Registered Member
Thread Starter
Join Date: Dec 2010
Location: Woodbridge
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
![VTECjunkie is an unknown quantity at this point](images/reputation/reputation_pos.gif)
![Default](images/icons/icon1.gif)
I'm new to doing swaps on my own so any help would be appreciated thanks. Well I recently swapped a jdm obd1 gsr into a 1992 civic hatch cx, I ran wires for vtec and also wires for a 4 wire o2 sensor. My question is why when I have the jdm p72 ecu hooked up the engine acts like its choking and it sounds almost like the internals are clicking and clacking for lack of better words but when I put a usdm p28 the car runs fine. Is there something I'm missing or wired wrong? What ecu can I use to get the full potential out of the motor? If anybody can help I would appreciate thanks.
Last edited by VTECjunkie; 12-20-2010 at 12:54 AM.
#3
Registered Member
Thread Starter
Join Date: Dec 2010
Location: Woodbridge
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
![VTECjunkie is an unknown quantity at this point](images/reputation/reputation_pos.gif)
![Default](images/icons/icon1.gif)
No its not boosted, the noise is almost like a metal on metal sound. It only does it when I plug the jdm p72 ecu in it and when I plug the p28 ecu it runs normal. Is there a reason why the jdm ecu that belongs to this motor doesnt work.
#6
RIP DRAGVA-2016
Join Date: Sep 2008
Location: super secret
Posts: 17,242
Likes: 0
Received 0 Likes
on
0 Posts
![NasTHatch](images/reputation/reputation_pos.gif)
![NasTHatch](images/reputation/reputation_pos.gif)
![NasTHatch](images/reputation/reputation_pos.gif)
![NasTHatch](images/reputation/reputation_pos.gif)
![NasTHatch](images/reputation/reputation_pos.gif)
![NasTHatch](images/reputation/reputation_highpos.gif)
![NasTHatch](images/reputation/reputation_highpos.gif)
![NasTHatch](images/reputation/reputation_highpos.gif)
![NasTHatch](images/reputation/reputation_highpos.gif)
![NasTHatch](images/reputation/reputation_highpos.gif)
![NasTHatch](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
jdm doesn't mean superior,run the p28
#10
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_pos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Fabrik8](images/reputation/reputation_highpos.gif)
![Default](images/icons/icon1.gif)
If you're using the dual runner GSR manifold with the secondary IABs, the P28 won't have control for that. Also, P28s don't have a knock sensor board, so no knock sensor functionality (that's the only physical difference between a P28 and a P30 in case you're wondering). A P28 will have fuel and ignition maps for the single cam engine, so it's not really ideal for a GSR engine.
The P72 ECU you already have should work perfectly on that engine, so there is something else happening here.
My first thought is that you need to run wires for the knock sensor and for the IAB control (for the GSR intake manifold). The P28 doesn't care about either of those things, which probably explains the difference between the two ECUs.
So you're still missing some wiring, that's the quick answer.
The P72 ECU you already have should work perfectly on that engine, so there is something else happening here.
My first thought is that you need to run wires for the knock sensor and for the IAB control (for the GSR intake manifold). The P28 doesn't care about either of those things, which probably explains the difference between the two ECUs.
So you're still missing some wiring, that's the quick answer.