B&T Motorsports in Lorton, VA
11-22-2007 | 06:27 AM
#1
Thread Starter
<3's Photography
Joined: Apr 2004
Posts: 1,154
Likes: 0
Received 0 Likes
on
0 Posts
From: Fairfax, VA
B&T Motorsports in Lorton, VA
I'm going to make this really simple.
- I needed a testpipe fabricated to allow me to put my stock exhaust back on due to a ticket.
- I called at 12pm on a Wednesday to ask about the service and shop availability. They said to bring it in.
- I dropped the car off after work at 6-7pm that same day. I requested that my car be completed by Thursday at noon (lunch time) bc it would've been very convenient for me.
- Thursday ~9am I got a call with an estimate. It was very reasonable.
- At 12pm I got a call saying that my car was completed and ready for pickup
- I picked the car up later that day and everything went smoothly from there.
Quality of work:
- I had a small test pipe made. It was a straight 3 inch pipe with a slight bend. They used stainless steel piping and flanges. They also used new gaskets and silicone gel to prevent leaks. The welds look perfect and matched the welds on my current downpipe.
- Wastegate recirc. was pretty simple. They just welded a small pipe to connect my dump pipe to the downpipe.
- All of the work was done well and I have no exhaust leaks.
Time:
- My car was in and out of the shop in less than 24 hours of my initial phone call.
- It was very prompt and convenient for me bc I had to go to court the following week
I used B&T before when I had my SR20 240. They installed a e-cutout on it a few years ago. The reason why I called them for my IS300 and not PFS is bc they were local and I had a good transaction with them in the past. They again proved their loyalty, craftsmanship, and professionalism. If I need anything else done to one of my cars, I will return to them
Thank you very much B&T.
Visit their site at: http://bandtmotorsports.com/
- I needed a testpipe fabricated to allow me to put my stock exhaust back on due to a ticket.
- I called at 12pm on a Wednesday to ask about the service and shop availability. They said to bring it in.
- I dropped the car off after work at 6-7pm that same day. I requested that my car be completed by Thursday at noon (lunch time) bc it would've been very convenient for me.
- Thursday ~9am I got a call with an estimate. It was very reasonable.
- At 12pm I got a call saying that my car was completed and ready for pickup
- I picked the car up later that day and everything went smoothly from there.
Quality of work:
- I had a small test pipe made. It was a straight 3 inch pipe with a slight bend. They used stainless steel piping and flanges. They also used new gaskets and silicone gel to prevent leaks. The welds look perfect and matched the welds on my current downpipe.
- Wastegate recirc. was pretty simple. They just welded a small pipe to connect my dump pipe to the downpipe.
- All of the work was done well and I have no exhaust leaks.
Time:
- My car was in and out of the shop in less than 24 hours of my initial phone call.
- It was very prompt and convenient for me bc I had to go to court the following week
I used B&T before when I had my SR20 240. They installed a e-cutout on it a few years ago. The reason why I called them for my IS300 and not PFS is bc they were local and I had a good transaction with them in the past. They again proved their loyalty, craftsmanship, and professionalism. If I need anything else done to one of my cars, I will return to them
Thank you very much B&T.
Visit their site at: http://bandtmotorsports.com/
Last edited by 240dreams; 11-22-2007 at 07:11 AM.
12-10-2007 | 10:24 AM
#3
B4NNED
Joined: Nov 2003
Posts: 522
Likes: 0
Received 0 Likes
on
0 Posts
Re: B&T Motorsports in Lorton, VA
I'm going to make this really simple.
- I needed a testpipe fabricated to allow me to put my stock exhaust back on due to a ticket.
- I called at 12pm on a Wednesday to ask about the service and shop availability. They said to bring it in.
- I dropped the car off after work at 6-7pm that same day. I requested that my car be completed by Thursday at noon (lunch time) bc it would've been very convenient for me.
- Thursday ~9am I got a call with an estimate. It was very reasonable.
- At 12pm I got a call saying that my car was completed and ready for pickup
- I picked the car up later that day and everything went smoothly from there.
Quality of work:
- I had a small test pipe made. It was a straight 3 inch pipe with a slight bend. They used stainless steel piping and flanges. They also used new gaskets and silicone gel to prevent leaks. The welds look perfect and matched the welds on my current downpipe.
- Wastegate recirc. was pretty simple. They just welded a small pipe to connect my dump pipe to the downpipe.
- All of the work was done well and I have no exhaust leaks.
Time:
- My car was in and out of the shop in less than 24 hours of my initial phone call.
- It was very prompt and convenient for me bc I had to go to court the following week
I used B&T before when I had my SR20 240. They installed a e-cutout on it a few years ago. The reason why I called them for my IS300 and not PFS is bc they were local and I had a good transaction with them in the past. They again proved their loyalty, craftsmanship, and professionalism. If I need anything else done to one of my cars, I will return to them
Thank you very much B&T.
Visit their site at: http://bandtmotorsports.com/
- I needed a testpipe fabricated to allow me to put my stock exhaust back on due to a ticket.
- I called at 12pm on a Wednesday to ask about the service and shop availability. They said to bring it in.
- I dropped the car off after work at 6-7pm that same day. I requested that my car be completed by Thursday at noon (lunch time) bc it would've been very convenient for me.
- Thursday ~9am I got a call with an estimate. It was very reasonable.
- At 12pm I got a call saying that my car was completed and ready for pickup
- I picked the car up later that day and everything went smoothly from there.
Quality of work:
- I had a small test pipe made. It was a straight 3 inch pipe with a slight bend. They used stainless steel piping and flanges. They also used new gaskets and silicone gel to prevent leaks. The welds look perfect and matched the welds on my current downpipe.
- Wastegate recirc. was pretty simple. They just welded a small pipe to connect my dump pipe to the downpipe.
- All of the work was done well and I have no exhaust leaks.
Time:
- My car was in and out of the shop in less than 24 hours of my initial phone call.
- It was very prompt and convenient for me bc I had to go to court the following week
I used B&T before when I had my SR20 240. They installed a e-cutout on it a few years ago. The reason why I called them for my IS300 and not PFS is bc they were local and I had a good transaction with them in the past. They again proved their loyalty, craftsmanship, and professionalism. If I need anything else done to one of my cars, I will return to them
Thank you very much B&T.
Visit their site at: http://bandtmotorsports.com/
Glad everything worked out well.
12-10-2007 | 10:26 AM
#4
B4NNED
Joined: Nov 2003
Posts: 522
Likes: 0
Received 0 Likes
on
0 Posts
Re: B&T Motorsports in Lorton, VA
Are you saying that B&T blew up your motor? I'm confused by what you are trying to say here. Also, how did you have a bad experience with them. Your message is not very clear but a few more details would fix that. Please give me some more info!
12-12-2007 | 09:03 AM
#6
Full Access Member
Joined: Oct 2007
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
From: springfield
12-12-2007 | 09:07 AM
#7
Retards.
Joined: Nov 2002
Posts: 1,180
Likes: 0
Received 0 Likes
on
0 Posts
From: nonyabizness
Re: B&T Motorsports in Lorton, VA
Definitely a big thumbs up for B&T, I've always had great customer service, fair pricing, and have never had any issues from any work I've had them do.
