BAD ASS honda parts. EK part out.
Thread Starter
Registered Member
Joined: Aug 2005
Posts: 138
Likes: 0
BAD ASS honda parts. EK part out.
All stuff is B series.
97 EK hatch w/ 00 front end conversion w ctr lights. Has a 6 point roll cage but can be removed if needed. includes SI gauge cluster, stock B series mounts, walbro 255. also has all the solid bushings in the front end and extended wheel studs.It has a carbon hood (needs re clearing) duck bill and front lip. and a momo steering wheel oh yea its wire tucked and comes w/ skunk2 drag coilovers. $3000
IM NOT SELLING THE GAUGE CLUSTER by itself
complete LS Vtec long block (valve cover to oil pan ready to run) $2900
motor has 20 passes on it. itd cost 6k to build from scratch.
B16 head race ported w crower springs and retainers $850
880cc seimens injectors w/ resistor pack $175
Crower stg2 turbo cams $300
B18 block w/ eagle rods wiesco pistons 9:1 w/ 20 quarter mile passes still running right now. includes everything from the deck to the pan. even throw in the oil lines for turbo and vtec head. $1600
ACT 6 puck clutch w/ race flywheel $200
corbeau race seat non adjustable $120
MSD 6AL w 3 step module $250
turbonetics stg5 60-1 (good for 550whp) $500
Custom tubular race turbo manifold and 4in down pipe $650
Tial 44mm wastegate $175
HUGE front mount intercooler $450
CROME chipped ecu w conversion harness for obd2a $300
obd2 distributor w MSD cap and coil $225
B series shift linkage w solid bushings $150
ATI harmonic balancer pulley $225
4in mandrel exhaust for EK $300
MSD blaster coil and cap $30
any questions pm or call 757 339 6495 scott
the car is still completely together w all this stuff and is for sale as a whole. it make 465whp w these parts. I jus want a new project. also location is portsmouth at MRD formally millennium autosports
97 EK hatch w/ 00 front end conversion w ctr lights. Has a 6 point roll cage but can be removed if needed. includes SI gauge cluster, stock B series mounts, walbro 255. also has all the solid bushings in the front end and extended wheel studs.It has a carbon hood (needs re clearing) duck bill and front lip. and a momo steering wheel oh yea its wire tucked and comes w/ skunk2 drag coilovers. $3000
IM NOT SELLING THE GAUGE CLUSTER by itself
complete LS Vtec long block (valve cover to oil pan ready to run) $2900
motor has 20 passes on it. itd cost 6k to build from scratch.
B16 head race ported w crower springs and retainers $850
880cc seimens injectors w/ resistor pack $175
Crower stg2 turbo cams $300
B18 block w/ eagle rods wiesco pistons 9:1 w/ 20 quarter mile passes still running right now. includes everything from the deck to the pan. even throw in the oil lines for turbo and vtec head. $1600
ACT 6 puck clutch w/ race flywheel $200
corbeau race seat non adjustable $120
MSD 6AL w 3 step module $250
turbonetics stg5 60-1 (good for 550whp) $500
Custom tubular race turbo manifold and 4in down pipe $650
Tial 44mm wastegate $175
HUGE front mount intercooler $450
CROME chipped ecu w conversion harness for obd2a $300
obd2 distributor w MSD cap and coil $225
B series shift linkage w solid bushings $150
ATI harmonic balancer pulley $225
4in mandrel exhaust for EK $300
MSD blaster coil and cap $30
any questions pm or call 757 339 6495 scott
the car is still completely together w all this stuff and is for sale as a whole. it make 465whp w these parts. I jus want a new project. also location is portsmouth at MRD formally millennium autosports
Last edited by TurboHonda; Sep 12, 2007 at 07:19 AM.
Thread Starter
Registered Member
Joined: Aug 2005
Posts: 138
Likes: 0
Re: BAD ASS honda parts. EK part out.
The throttle body is polished aluminum and comes w/ tps. The clutch has some decent miles on it but its holding 450whp so id say its good and the flywheel is 10lb i think.
