1989 Nissan Hardbody/ Frontier Project
Thread Starter
Registered Member
Joined: Apr 2007
Posts: 231
Likes: 0
From: Richmond
1989 Nissan Hardbody/ Frontier Project
Name: Jason
Contact: PM
Price: 3000 OBO
Trade for Macbook/Pro with cash or if you can get a hold of those cdj1000mk3's and djm 800mixer for an even trade
Location: Richmond
1989 NISSAN 2WD HARDBODY TRUCK WITH A 2000 FRONTIER FRONT END CONVERSION Bagged
Body: 151K original miles on it.
Engine:
Stock Z2.4L 8 spark plug 4 cylinder
42K with new engine
150K on swapped 1991 2wd transmission
Less than 500 miles on new Clutch
K&N Air Filter
Reverse Electric Fan
Red Top Deep Cycle Battery
Suspension:
Custom 2-link with 1/2" M.I.C. Manual valves
Firestone 2500lb/2600 Airbags
front and rear Toxic Shocks
5 Gal. 6 port air tank mounted under bed
AIM Industries 3/4 HP Air compressor with oiler and 150 psi pressure switch mounted to bed
Exterior:
2000 Nissan Frontier Front end grafted to the 1989 Fenders
Lower Valance is off due to a hard bottom out, it's broken but I still have it if you want it.
Tapered body line
Shaved:
Bed with trailer fenders and LINE-X'ED
Door handles
hood squirters
wiper cowl
Mirrors
Antennae
Bed rails (need to be finished)
Inner Fenders
Tailgate w/ droptag
Interior:
1996 Isuzu Amigo Bucket Seats
Center console (temporary)
Wheels:
15" Nissan Pathfinder Chrome Rims on Low Pro tires
I have most of the papers of the work I have had done, and plenty of pictures if you want them.
Extras included!! Dynamat Extreme, 2 exrta sets of tail lights, brand new phoenix alarm, audiobahn EQ, Audiobahn 4 gauge amp kit(not pictured), Kole Audio 1.5 Power cap(not pictured), Trailer fenders for the frontend(not pictured)
Everything is brand new exept for the tail lights that I used for a couple of months, but are in great condition.
Contact: PM
Price: 3000 OBO
Trade for Macbook/Pro with cash or if you can get a hold of those cdj1000mk3's and djm 800mixer for an even trade
Location: Richmond
1989 NISSAN 2WD HARDBODY TRUCK WITH A 2000 FRONTIER FRONT END CONVERSION Bagged
Body: 151K original miles on it.
Engine:
Stock Z2.4L 8 spark plug 4 cylinder
42K with new engine
150K on swapped 1991 2wd transmission
Less than 500 miles on new Clutch
K&N Air Filter
Reverse Electric Fan
Red Top Deep Cycle Battery
Suspension:
Custom 2-link with 1/2" M.I.C. Manual valves
Firestone 2500lb/2600 Airbags
front and rear Toxic Shocks
5 Gal. 6 port air tank mounted under bed
AIM Industries 3/4 HP Air compressor with oiler and 150 psi pressure switch mounted to bed
Exterior:
2000 Nissan Frontier Front end grafted to the 1989 Fenders
Lower Valance is off due to a hard bottom out, it's broken but I still have it if you want it.
Tapered body line
Shaved:
Bed with trailer fenders and LINE-X'ED
Door handles
hood squirters
wiper cowl
Mirrors
Antennae
Bed rails (need to be finished)
Inner Fenders
Tailgate w/ droptag
Interior:
1996 Isuzu Amigo Bucket Seats
Center console (temporary)
Wheels:
15" Nissan Pathfinder Chrome Rims on Low Pro tires
I have most of the papers of the work I have had done, and plenty of pictures if you want them.
Extras included!! Dynamat Extreme, 2 exrta sets of tail lights, brand new phoenix alarm, audiobahn EQ, Audiobahn 4 gauge amp kit(not pictured), Kole Audio 1.5 Power cap(not pictured), Trailer fenders for the frontend(not pictured)
Everything is brand new exept for the tail lights that I used for a couple of months, but are in great condition.
Last edited by jmills62; Feb 26, 2009 at 02:31 PM.
Thread Starter
Registered Member
Joined: Apr 2007
Posts: 231
Likes: 0
From: Richmond
Re: FS:FT 1989 Nissan Hardbody/ Frontier Project
you're telling me..
It's been a headache, and most of the time it was my daily driver while trying to get work done on it. Now I'm just out of money and patience.
It's been a headache, and most of the time it was my daily driver while trying to get work done on it. Now I'm just out of money and patience.
