Anyone know how to install door pins on S10/Blazers?
#1
Enthusiast
Thread Starter
Join Date: Mar 2003
Location: Durham, NC
Posts: 217
Likes: 0
Received 0 Likes
on
0 Posts
Anyone know how to install door pins on S10/Blazers?
If you're reading, you probably know exactly what im talkin about (door sags when you open it)
If you know how to install them (as in you've done it), hit me up, i'll pay you for your services..
I need them put in asap..
If you know how to install them (as in you've done it), hit me up, i'll pay you for your services..
I need them put in asap..
#2
Registered Member
Join Date: Mar 2004
Location: Newport News
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
Re: Anyone know how to install door pins on S10/Blazers?
I have a jimmy and it is simialir and I wrecked it but have to replace the doors and it was a pain to put the pins in alll I can say is I remember a clip that is metal sliding over the pin that you hammer down the pin but to take them out I would probley say you would have to prie that piece of metal off
#4
Re: Anyone know how to install door pins on S10/Blazers?
Where are you located? Its not the hardest thing to do. The worst part is getting the spring back in. The bushings that the pin slides through are worn out. If you feel like driving to Moyock then I can help you out. Just buy me a burger or something.
#5
whats hood?
Join Date: Nov 2002
Location: Downtown
Posts: 2,830
Likes: 0
Received 0 Likes
on
0 Posts
Re: Anyone know how to install door pins on S10/Blazers?
You just need a crowbar, a punch, a hammer, some wd40. get the spring out, then spray down the door pins and use the punch and hammer to beat the old pins out.
but you should get a door spring compressor, because getting that spring back in is a mother.
but you should get a door spring compressor, because getting that spring back in is a mother.
#6
takin it all
Join Date: Jan 2003
Location: 757/PA/MD/Boston,MA
Posts: 6,934
Likes: 0
Received 0 Likes
on
0 Posts
Re: Anyone know how to install door pins on S10/Blazers?
Originally Posted by BMW E30SIX
If you're reading, you probably know exactly what im talkin about (door sags when you open it)
If you know how to install them (as in you've done it), hit me up, i'll pay you for your services..
I need them put in asap..
If you know how to install them (as in you've done it), hit me up, i'll pay you for your services..
I need them put in asap..
how did this go?
i have to do the same for my driverside door on my truck
#7
Enthusiast
Thread Starter
Join Date: Mar 2003
Location: Durham, NC
Posts: 217
Likes: 0
Received 0 Likes
on
0 Posts
Re: Anyone know how to install door pins on S10/Blazers?
Well, I havent gotten around to it yet...
I want to do it soon, so it does not cause any damage..
let's have a door pin installation party everyone... ok... or not...
I want to do it soon, so it does not cause any damage..
let's have a door pin installation party everyone... ok... or not...
#8
corona connessuer
Join Date: Nov 2002
Location: GUAM
Posts: 3,425
Likes: 0
Received 0 Likes
on
0 Posts
Re: Anyone know how to install door pins on S10/Blazers?
Originally Posted by BMW E30SIX
Well, I havent gotten around to it yet...
I want to do it soon, so it does not cause any damage..
let's have a door pin installation party everyone... ok... or not...
I want to do it soon, so it does not cause any damage..
let's have a door pin installation party everyone... ok... or not...
#9
The Pro to call.
Join Date: Jul 2003
Location: under cars.
Posts: 6,172
Likes: 0
Received 0 Likes
on
0 Posts
Re: Anyone know how to install door pins on S10/Blazers?
if you cant install them in less than 45 minutes, you suck as an individual. hell, even the old dude here can do a set in about 20 minutes.
a door spring compressor is about 15 bucks, i highly reccommend one.
a door spring compressor is about 15 bucks, i highly reccommend one.
#10
Enthusiast
Thread Starter
Join Date: Mar 2003
Location: Durham, NC
Posts: 217
Likes: 0
Received 0 Likes
on
0 Posts
Re: Anyone know how to install door pins on S10/Blazers?
Originally Posted by fc735
if you cant install them in less than 45 minutes, you suck as an individual. hell, even the old dude here can do a set in about 20 minutes.
a door spring compressor is about 15 bucks, i highly reccommend one.
a door spring compressor is about 15 bucks, i highly reccommend one.
oh ok.. interesting..
Thread
Thread Starter
Forum
Replies
Last Post