Adventures into the unknown...

Reply Subscribe

Thread Tools

Aug 23, 2009 | 03:01 PM

#11

BSeriesTurbo

Go Team Marlboro

Joined: Jul 2003

Posts: 2,419

Likes: 0

From: Roanoke, VA

Re: Adventures into the unknown...

Needs decent work, motor work needed a plus

I'd like for it to be titleable.

Aug 23, 2009 | 03:12 PM

#12

VanillaThrilla

wub wub wub wub

Joined: Sep 2004

Posts: 19,724

Likes: 0

From: Virginia

Re: Adventures into the unknown...

So if motor work being needed is a plus, would you rather have a relatively clean rolling shell without the motor for little to nothing if I can find one?

Aug 23, 2009 | 03:47 PM

#13

TNGChris

Registered member

Joined: May 2006

Posts: 3,781

Likes: 0

From: Roanoke

Re: Adventures into the unknown...

Quote:

Originally Posted by bluesrt2004

Haha most definately . When's that Coupe comin back out to play?

Seems like never.I just don't have any time after I work on other people's stuff.

Quote:

Originally Posted by Lv2 Turn

Well the trans you see above is shot. The case has actually been cracked on the end near the snap ring and bearings. So Im just fixing the trans that had a bad Input shaft bearing. :P

If most of the other stuff looks decent,I'd save it.You can easily replace either/both case halves-you just have to check and reshim the shafts and diff.

Quote:

Originally Posted by BSeriesTurbo

Sounds like time to upgrade to a B, or better yet a K

BTW, Chris, seen any busted up e36's fo sale?

I haven't been looking,but when I was looking for my car I did find several close,cheap non-M cars.

Last edited by TNGChris; Aug 23, 2009 at 03:51 PM.

Aug 23, 2009 | 03:49 PM

#14

TNGChris

Registered member

Joined: May 2006

Posts: 3,781

Likes: 0

From: Roanoke

Re: Adventures into the unknown...

Quote:

Originally Posted by Lv2 Turn

Well the trans you see above is shot. The case has actually been cracked on the end near the snap ring and bearings. So Im just fixing the trans that had a bad Input shaft bearing. :P

If most of the other stuff looks decent,I'd save it.You can easily replace either/both case halves-you just have to check and reshim the shafts and diff.

Aug 23, 2009 | 04:53 PM

#15

BSeriesTurbo

Go Team Marlboro

Joined: Jul 2003

Posts: 2,419

Likes: 0

From: Roanoke, VA

Re: Adventures into the unknown...

Quote:

Originally Posted by VanillaThrilla

So if motor work being needed is a plus, would you rather have a relatively clean rolling shell without the motor for little to nothing if I can find one?

Would be very nice

Aug 25, 2009 | 05:32 AM

#16

Colby 92' RS

Got Torque?

Joined: Aug 2009

Posts: 12

Likes: 0

From: Fincastle

Re: Adventures into the unknown...

Quote:

Originally Posted by Lv2 Turn

Well the trans you see above is shot. The case has actually been cracked on the end near the snap ring and bearings. So Im just fixing the trans that had a bad Input shaft bearing. :P

WOW ! That looks great chris !! sorry man. i bet that one sounded good. I hope you find another tranny fast !

Aug 25, 2009 | 08:02 AM

#17

.Sarge.

Thread Starter

EDM|Mugen|MK3 CRX

Joined: Mar 2008

Posts: 2,989

Likes: 0

From: Midwest and Virginia

Re: Adventures into the unknown...

Quote:

Originally Posted by Colby 92' RS

WOW ! That looks great chris !! sorry man. i bet that one sounded good. I hope you find another tranny fast !

Just got a call from the dealer and my parts are in so Ill be putting the puzzle back together tomorrow and installing the tranny back in the car on saturday.